| |
|
JS•2
• JS•3
|
Look
inside a JS•2
or JS•3
and you will find the build quality and components to be of
only the highest professional standards. Radial's proven construction
methods and materials ensure highest performance and years of
trouble-free service. The JS•2
and JS•3
feature Jensen transformers – the best
audio transformers in the industry – to achieve the highest
possible signal integrity and phase coherence while eliminating
hum and buzz caused by ground loops.
|
|
| |
|
 Inside
the JS•2
(click to view JS•3) |
| |
1. |
Isolated
XLR connectors to eliminate chassis ground potential. |
| |
2. |
Jensen
audio transformer on input provides 100% isolation
to eliminate hum and noise causing ground loops. |
| |
3. |
Military
spec PC board with full surface ground plane to reduce
susceptibility to RF noise. |
| |
4. |
High
grade switches - long life, high cycle for reliable
performance. |
| |
5. |
14-gauge
steel welded I-beam construction makes it virtually
impossible to torque the PC board. |
|
|
|
| |
|
JS•2
Input and Output Panels |
| |
6. |
PAD
Input 30dB - reduces the level going in from loud sources that
could overload the circuit and cause distortion. |
| |
7. |
INPUT
Microphone 600 Ohm - balanced input,
female XLR connector, AES standard with Pin-1 ground and Pin-2
hot. |
| |
8. |
THRU
Direct-1 600 Ohm - direct output
1 (of 2) male XLR connector, AES standard with Pin-1 ground
and Pin-2 hot. |
| |
9. |
Book-end
design creates a protective zone around the switches
& connectors – indestructible 14-gauge steel construction.
|
| |
10. |
Full
no-slip rubber bottom pad provides mechanical isolation,
electrical insulation and prevents unit from sliding around. |
| |
11. |
Heavy-duty
baked enamel finish for excellent durability and great
looks for years! |
| |
12. |
THRU
Direct-2 600 Ohm - direct output
2 (of 2) male XLR connector, AES standard with Pin-1 ground
and Pin-2 hot. |
| |
13. |
LIFT
Ground Pin-1 - switch lifts pin-1 for the 'Direct-2'
output. |
| |
14. |
OUTPUT
Isolated-1 600 Ohms - balanced male XLR output connector; AES
standard with Pin-1 ground and Pin-2 hot. |
| |
15. |
LIFT
Ground Pin-1 - switch lifts pin-1 of the 'OUTPUT' connector. |
|
| |
|
|
|
|
|
|
Construction
The JS•2
and JS•3 are
designed to withstand the rigors of high- use professional environments!
Radial's innovative 'book cover' design provides a protective zone
around the switches and connectors that keeps these components safe.
Stress
on circuitboards causes broken and intermittent solder joints, a
common cause of failure in commercial rental and other high-use
environments. Radial's 14-gauge welded I-beam inner chassis and
14-gauge outer shell greatly reduce the possibility of torque stresses
being applied to the PC board.
A full-bottom
no-slip rubber pad works double duty by (a) providing protection
from electrical shock and (b)
assuring that these splitters won’t slip and slide around.
|
|
|
JS•2
Specifications |
Input
impedance: |
1.06kOhms
(1kHz, -20dBu) |
Insertion
loss: |
.8dB |
Voltage
gain: |
-.82dB
(1kHz, -20dBu) |
Deviation
from linear phase: |
+3.3/-0°
(20Hz to 20kHz, -20dBu) |
Frequency
Response: |
10Hz
to 80kHz |
Distortion
(THD): |
0.001%
(1kHz, -20dBu)
0.05% (20Hz, -20dBu) |
Maximum
input level: |
+2.0dBu
(20Hz, 1% THD) |
| Common-mode
rejection ratio (CMRR): |
130dB
(60Hz)
95dB (3kHz) |
Output
Impedance: |
245
Ohms |
Size
(H x W x D): |
Size
(H x W x D): 2” x 3.25” x 5” |
Weight: |
1.95lbs
/ .9kg |
Construction: |
14-gauge
steel chassis & shell, baked enamel finish |
| Warranty: |
3
years on device, 20yrs on Jensen transformers |
|
| |
